Car Key Button Repair
A damaged car key button can be frustrating. You may need to contact a 24-hour Locksmith Service or purchase a replacement remote.
You could save money by fixing your old key fob rather than replacing it. This is especially true if a worn-out switch or faulty contacts are at the root of the problem.
Battery
If the buttons on the key fob aren't responding to pressing it, it could be an obvious indication that your battery is dying or nearing the end of its life. It's simple to replace the battery on your own, rather than paying for locksmiths or dealers.
First find the battery compartment. The battery compartment is typically located on the back of the key fob and is often concealed behind a cover that slides out or an open button that opens the access point. Once the compartment is exposed then you will find the small cell battery. This is typically shaped like a coin and identified with an minus and plus sign. Take the battery out and replace it with a new one in its place, making sure that the plus and minus signs are aligned correctly.
Close the compartment and snap together the two halves of your key fob. Before closing the door make sure to align and snap the components into the correct position. Press any of the buttons to verify that they function correctly.
If your remote keyfob isn't working after replacing the battery, there could be other problems that require a different type of repair. Physical damage from dropping the fob in a puddle, for instance could cause it to stop working completely. Or, it could be experiencing an internal electrical problem or it may require to be deprogrammed by an expert or locksmith. Find out what's wrong with your key fob using these other common methods for troubleshooting your car.
Switches
Depending on the year and manufacturer, there are various types of switches on the keyfob of your car. The older model keys usually have a separate chip that you can see in the case, while the newer keys are more advanced and function by sending signals to the car. The buttons on a key may be worn out or damaged through regular use, irrespective of the model. They can become difficult to press or not responsive. If you force the button, it could cause further damage. It could also stop the key from functioning in the future.
If you are unable to get your key to function Try changing the batteries. If that doesn't work it may be necessary to clean the key's fob and re-adjust the switches. These tiny electronic switches are more likely than larger components of the key to break because they are constantly tossed around.
The switches feel rubbery and are coated with an electrical conductor. The film is prone to fade over time. However, they're small and inexpensive to replace. The old ones are soldered to the circuit board so you'll need to be careful to remove them without causing any damage to anything else. keys repair can then solder the new ones into and reassemble your fob.
A good way to keep your car key fob from becoming ruined is to avoid using it for longer than a couple of hours at a time and to keep it out of the way in places in areas where it is visible. Also, make sure you locate a safe place to keep your key in when you aren't making use of it.
If you've already tried cleaning your key fob or replacing the battery, but the issue persists it's time to consider an appointment with a locksmith. A professional can check the frequency of your key to determine if it's still able to communicate with your vehicle, open and replace micro switches, change cases and more.
Outer Case
A key fob spends many hours bouncing around, and if the buttons aren't free to move up and down within the case they can get stuck or break. If changing the battery or cleaning it with the help of a cotton swab or rubbing alcohol doesn't fix the issue, then removing the case and checking it out could be required. If the contacts where the buttons touch aren't fitting well or are worn out, adjusting them could be the only solution to fix the problem.
key repair service get worn out over time. The rubber expands, nails gouge into it and the buttons can become difficult to press. In this situation the key may fail and it's time to replace the case or the buttons. This repair involves disassembling the remote, locating the buttons on the circuit board, then heating the solder, and then carefully remove them. New buttons are then attached to the circuit board. The case can be reassembled, and the horseshoe key blade can be attached. The new buttons must be securely fitted inside the case to prevent them from falling out.
Inner Case
Over time the buttons on your key fob can be damaged or stuck because of the constant jolting and accidental pressing. With keys repair of metal tape and a hole punch you can often quickly fix this problem when your car is not at home and the key fob doesn't work and you are unable to open the doors, but not start the engine. This simple fix can allow you to return safely to your vehicle and complete your trip.